91精品在线播放-国产九九-亚洲乱码中文字幕-国产乱论视频-国产精品亚洲一区二区三区-久久久五月-日本黄色大片免费-麻豆视频传媒入口-麻豆chinese极品少妇-免费av的网站-亚洲欧美男人天堂

Tel:400-800-6106 WeChat Label Website map 簡EN

Shenzhen NTEK Testing Technology Co., Ltd.

Current location : Home > Services> Testing> Reliability Testing
?

Services

Contact us +

Hot Line 400-800-6106
NTEK Group
Tel:+86 18926052263 Email:ntek@ntek.org.cn No.24,Xinfa East Road,Xinqiao Street,Baoan District,Shenzhen

Drop Testing

Test Overview

Drop testing is divided into package drop testing and bare product drop testing. Package drop testing mainly assesses a product's ability to withstand accidental drop impacts during transportation and storage, while bare product drop testing assesses its ability to withstand accidental drop impacts during normal use. Package drop testing also reflects how well the packaging protects the product when subjected to a vertical drop.

Drop height, number of drops and drop orientation determine the severity of the test. Different international standards specify different drop methods and drop heights for different products. For hand-held products (such as mobile phones and MP3 players), most drop heights range from 100cm to 150cm. IEC recommends that hand-held products of 2 kg or less should withstand a drop height of 100cm without damage, MIL recommends a drop height of 122cm, and Intel recommends a drop height of 150cm for hand-held products (such as mobile phones).

According to the reference standards, the drop surface shall be a smooth, hard, rigid surface of concrete or steel, or, where necessary, other floors such as marble.

Package Drop Testing

Package Drop Testing

General requirements for package drop testing: the drop sequence consists of one corner, three edges and six faces, in free fall.

Corner drop: after release, the test corner strikes the impact surface;

Edge drop: the bottom face of the sample is tilted to an angle of 20° to the horizontal, then raised to the test height and released, so that the edge strikes the impact surface;

Face drop: the face of the test sample must strike the impact surface directly after the drop.

Package drop testing determines whether the strength of the outer carton or inner box and the robustness of the product packaging meet quality requirements.

Bare Product Drop Testing

Bare Product Drop Testing

Purpose of bare product drop testing

Bare product drop testing is performed to check a product's ability to resist throwing and dropping during use. The method of releasing the test sample should allow it to fall freely from its suspended position, with minimum disturbance at release.


· ASTM standard test equipment requirements: the impact surface shall be covered with 3.0mm (1/8in) thick rubber flooring on top of concrete at least 64mm (2.5in) thick, with an area of not less than 3㎡.

· EN71 standard test equipment requirements: the impact surface consists of a 4mm thick steel plate coated with a 2mm thick layer of Shore hardness 75±5A, placed on a non-flexible horizontal surface.

· GB6675 standard test equipment requirements: the impact surface shall consist of a vinyl polymer sheet of approximately 3mm nominal thickness bonded to concrete at least 64mm thick; the surface shall have a Shore hardness of A80 ±10, with an area of at least 0.3㎡.

Test Standards

GB/T2423.8 Environmental testing for electric and electronic products, Part 2: Test methods, Test Ed: Free fall.

IEC60068-2-32 Test methods for free fall.

GB-T4857.5 Packaging, transport packages, Drop test method.

ASTM D 5276-98(2009)

Test Equipment and Instruments

Drop Testing


Obtaining quotations

Corporate name: *
Your name:*
Your cell phone and E-mail:*
Your needs:*

*For your benefit, your information will be kept strictly confidential

Submit successfully

Professional engineers will contact you quickly to provide you with appropriate solutions and look forward to meeting you~

Official Account Consulting
主站蜘蛛池模板: 昭平县| 汤原县| 金塔县| 孟州市| 西峡县| 同江市| 内乡县| 澄城县| 宁都县| 寻乌县| 大丰市| 达州市| 新民市| 云和县| 祁阳县| 棋牌| 曲松县| 罗田县| 花莲市| 凉山| 黄浦区| 汉阴县| 新余市| 唐河县| 武邑县| 辉县市| 新蔡县| 崇阳县| 宝清县| 桐柏县| 北辰区| 辉县市| 澳门| 成武县| 永泰县| 景洪市| 西贡区| 恭城| 甘谷县| 长子县| 彭山县|